Skip to content
Bitswrt

Contents

sysupgrade.bin 下载链接

升级固件

适用机种: N32,NPN,NPM

NHX53X2
NHX6018
NHX5018
NHX4019

升级sysupgrade

  • 查找sysupgrade.bin: openwrt-ipq-ipq60xx-NHX6018-0-NPN-256M32-D4-ubi-sysupgrade.bin
  • 更改升级程序名称;机种型号.bin NHX6018-0-NPN-256M32-D4.bin
  • 开启tftp sever
  • 机种型号.bin NHX6018-0-NPN-256M32-D4.bin 放入tftp sever 目录
  • 电脑以太网设置静态IP地址192.168.10.1
  • 电脑以太网直连板子的以太网端口
  • 串口线缆连接板子到计算机
  • 板子通电开机
  • 读取到 Hit any key to stop autoboot: 3 立马在串口打印处按下enter按键进入uboot:
  • 输入升级命令nhxrecovery
U-Boot 2016.01 (Feb 01 2024 - 17:31:03 +0000)


DRAM:  smem ram ptable found: ver: 2 len: 4
1 GiB
NAND:  ONFI device found
ID = 1580a1c2
Vendor = c2
Device = a1
oob size: 64
SPI_ADDR_LEN=3
SF: Detected MX25U6435F with page size 256 Bytes, erase size 64 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x800000
136 MiB
MMC:   <NULL>: 0
*** Warning - bad CRC, using default environment


PCI Link Intialized
In:    serial@78B1000
Out:   serial@78B1000
Err:   serial@78B1000
machid: 8030000
eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
eth2 MAC Address from ART is not valid
eth3 MAC Address from ART is not valid
eth4 MAC Address from ART is not valid
eth5 MAC Address from ART is not valid
Hit any key to stop autoboot:  0


Net:   MAC0 addr:0:3:7f:ba:db:ad
PHY ID1: 0x4d
PHY ID2: 0xd0b1
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq6018_edma_alloc_rings: successfull
ipq6018_edma_setup_ring_resources: successfull
ipq6018_edma_configure_rings: successfull
ipq6018_edma_hw_init: successfull
eth0
NHX6018-1-NPN-256M32-D4#
NHX6018-1-NPN-256M32-D4#
NHX6018-1-NPN-256M32-D4#
NHX6018-1-NPN-256M32-D4#
NHX6018-1-NPN-256M32-D4#
NHX6018-1-NPN-256M32-D4# nhxrecovery
nhx recovery
ipq6018_eth_halt: done
eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 up Speed :1000 Full duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 Down Speed :10 Half duplex
ipq6018_eth_init: done
Using eth0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.10
Filename 'NHX6018-1-NPN-256M32-D4.bin'.
Load address: 0x44000000
Loading: *
ARP Retry count exceeded; starting again